Independent investment casting knowledge for global buyersB2B Network
Investment Casting Hub
Industry Applications

How to Specify Tolerances for Investment Castings

Published 7 min read

An engineer measures a metal casting with a caliper.
Quick answer

Define tolerances by starting with the part function, then applying standard practice to each dimension. Align the drawing with the casting process, verify with the foundry, and document the final limits to prevent fit issues.

Key takeaways
  • Match tolerance values to the actual assembly requirement, not to a default standard.
  • Apply tighter limits only to dimensions that control fit, function, or sealing.
  • Review the drawing with the foundry before production to confirm manufacturability.
  • Keep a single revision of the drawing and control document to avoid confusion.

What defines a workable tolerance in investment casting

A tolerance is the acceptable variation from the nominal dimension on a drawing. In investment casting, the foundry controls this variation through the mold, the core, and the post-casting machining process. The goal for procurement is to define limits that protect the assembly while keeping the part within the capability of the casting process.

Tight tolerances on every dimension increase cost and risk. Many parts fit and function well with general limits on non-critical features. The workable tolerance for an investment casting is set by the part function, the material, and the available machining capability.

What to define before setting the limits

Before assigning a number to a dimension, define the following inputs.

  1. Part function. Identify what the part must do. A bearing housing needs a round bore. A valve seat needs a flat, concentric surface. A bracket needs to bolt to a mating plate.
  2. Assembly requirements. Determine the fit class. Is it a slip fit, a press fit, a transition fit, or a clearance fit? The assembly standard sets the minimum and maximum limits.
  3. Material and size. The casting material and the size of the feature affect shrinkage and the ability to hold a tight limit. Larger castings and some alloys present more variation.
  4. Post-casting operations. If a surface will be machined, the tolerance on the as-cast dimension must leave enough stock for that operation.
  5. Inspection method. The tolerance must match the measurement capability. A limit of 0.01 mm on a 200 mm bore cannot be verified with a standard micrometer in a typical shop.

The reason for each item is simple. If the function, fit, material, and inspection method are not clear, the tolerance number is just a guess, and the guess will fail in the field.

Step-by-step process for specifying tolerances

Follow these steps to assign tolerances on an investment casting drawing.

  1. Mark each dimension with a function code.
    Use a short code on the drawing: F for fit, S for seal, B for bearing, C for general. The reason is that the foundry and the buyer can see why a limit is tight. It prevents the default assumption that all dimensions need the same care.

  2. Apply the tightest limit only to F, S, and B dimensions.
    Fit, seal, and bearing features control the part. Apply a limit based on the assembly fit class. The reason is that these features determine whether the part goes together, seals, or carries load.

  3. Use general limits for all other dimensions.
    For C dimensions, use a general tolerance. The reason is that a general limit reduces drawing clutter and focuses inspection effort on the features that matter.

  4. Set the as-cast limit to leave stock for machining.
    If a bore will be turned, set the as-cast limit so the final machined size is within range. The reason is that the foundry must leave enough material for the machine to remove.

  5. State the surface finish on critical faces.
    For bearing seats and sealing surfaces, state the surface finish. The reason is that the foundry must know the target before it is machined, and the buyer can verify the final surface.

  6. Add a note for concentricity and perpendicularity.
    If a feature must line up with another feature, state the geometric tolerance. The reason is that a round bore is not enough if it is not centered to the housing face.

  7. Confirm the limits with the foundry.
    Send the drawing to the foundry before release. Ask them to check the limits against their process. The reason is that a limit that is possible on paper may not be possible in their mold and machine setup.

  8. Record the agreed limits in a control document.
    Keep the drawing and the foundry confirmation together. The reason is that a single source of truth prevents revision errors and mix-ups during production.

Tolerance values to consider for common features

The following table shows a general range of limits for common investment casting features. These are starting points for discussion, not a standard. Adjust them to the assembly requirement and the foundry capability.

Feature type General limit Tight limit
Outside diameter 0.50 mm 0.10 mm
Bore diameter 0.50 mm 0.10 mm
Thickness 0.50 mm 0.10 mm
Length 1.00 mm 0.25 mm
Flatness 0.50 mm 0.10 mm
Perpendicularity 0.50 mm 0.10 mm

The reason for this table is to give the buyer a baseline. If the assembly fits with a 0.50 mm general limit, do not specify 0.10 mm. If the part seals, specify 0.10 mm.

Common mistakes when specifying tolerances

  1. Specifying tight limits on every dimension.
    This increases cost and rejects parts that would have fit. The reason is that the foundry must control every feature, and the inspection time rises.

  2. Mixing units on one drawing.
    A drawing with millimeters and inches creates confusion. The reason is that a single unit system prevents conversion errors during inspection.

  3. Forgetting the as-cast stock requirement.
    If the drawing shows a final machined size but not the as-cast size, the foundry must guess. The reason is that the foundry must know how much material to leave for the machine.

  4. Ignoring geometric tolerances.
    A bore that is round but not perpendicular to the face will not seat. The reason is that geometric tolerances control the relationship between features, not just the size of each feature.

  5. Not reviewing the drawing with the foundry.
    A limit that is impossible in the foundry process will cause a debate later. The reason is that an early review prevents a late production stop.

Final verification step

Before releasing the drawing, run the following check.

  • Every dimension has a function code.
  • Tight limits are only on F, S, and B features.
  • General limits cover all C features.
  • As-cast stock is stated for machined features.
  • Surface finish is stated for critical faces.
  • Geometric tolerances are stated for relationships.
  • The foundry has confirmed the limits in writing.
  • The drawing number and revision are current.

The reason for this final step is to catch the small errors that cause large problems. A missing stock note or a missing geometric tolerance can fail a part in the field. A short check before release saves the cost of a rework.

What to do when the foundry says a limit is not possible

If the foundry says a limit is not possible, do not argue. Ask them to explain why. Common reasons include the mold shrinkage, the core strength, the machine capability, or the inspection method.

The buyer can then choose one of three paths.

  1. Relax the limit. If the part fits with a wider limit, accept it. The reason is that the part will still function.
  2. Add machining. If the limit must be tight, specify that the foundry will machine the feature. The reason is that machining can hold a tighter limit than the cast size.
  3. Change the part design. If the limit is critical and the foundry cannot hold it, change the design. The reason is that the part must be manufacturable.

The goal is a part that fits, functions, and is produced on time. The tolerance is a tool to make that happen.

How to write the tolerance note on the drawing

Use a clear, short note. Avoid long paragraphs.

Example:

“General tolerance: 0.50 mm unless otherwise noted.
Bore and outer diameter: 0.10 mm.
Surface finish: 1.6 µm on bearing seats.
Concentricity: 0.10 mm to housing face.
As-cast stock: 0.50 mm on all machined bores.
Units: millimeters.”

The reason for this format is that it is easy to read and easy to verify. The foundry can find the limit quickly. The inspector can find the limit quickly. The buyer can find the limit quickly.

How to handle revisions

When a part changes, update the drawing. Do not rely on verbal instructions. The reason is that a verbal instruction is not a record.

  • Change the drawing number and revision.
  • State the change in the revision block.
  • Send the new drawing to the foundry.
  • Confirm the foundry has the new revision.
  • Archive the old revision.

The reason for this process is to prevent the use of an old drawing. An old drawing has old limits. The part must be made to the current limits.

How to verify the part after production

After the part is made, verify the critical features.

  • Measure the F, S, and B dimensions.
  • Check the surface finish on critical faces.
  • Check the geometric tolerances.
  • Compare the results to the drawing limits.
  • Record the results.

The reason for this verification is to confirm that the part meets the specification. If the part fails, the buyer has a record to return to the foundry.

How to close the process

The process is complete when the drawing is released, the foundry confirms the limits, the part is made, and the part is verified. The reason for this sequence is that each step builds on the last. A missing step breaks the chain.

The tolerance is not a guess. It is a limit set by the part function, the assembly requirement, and the manufacturing capability. When the limit is clear, the part fits. When the limit is clear, the cost is controlled. When the limit is clear, the process is predictable.

Frequently asked questions

What is the standard tolerance for investment casting?

There is no single standard. The limit depends on the part function and the assembly requirement. Use a general limit for non-critical features and a tighter limit for fit, seal, and bearing features.

How tight can an investment casting be?

The tightness depends on the size, the material, and the post-casting machining. Small castings and machined features can hold tight limits. Large castings and non-machined features usually need wider limits.

Do I need to specify a tolerance on every dimension?

No. Use a general limit for most dimensions. Specify a tighter limit only on features that control fit, function, or sealing. This reduces drawing clutter and focuses inspection.

What if the foundry says a limit is not possible?

Ask them to explain why. Then choose to relax the limit, add machining, or change the part design. The goal is a part that fits and is manufactured on time.

How do I verify the part after production?

Measure the critical dimensions, check the surface finish, and verify the geometric tolerances. Compare the results to the drawing limits and record the results.