Independent investment casting knowledge for global buyersB2B Network
Investment Casting Hub
Industry Applications

Checklist: Verifying Foundry Capability for Titanium

Published Updated 6 min read

A worker inspects a titanium ingot in a foundry
Quick answer

This checklist helps buyers verify foundry capability for titanium investment casting. It covers aerospace casting, titanium casting, and investment casting applications. Use it to audit heat treatment, quality control, and process controls before releasing a purchase order.

Key takeaways
  • Check heat treatment capability for titanium, including vacuum or controlled-atmosphere furnaces
  • Review raw material traceability and supplier controls for titanium billets
  • Confirm dimensional inspection methods for complex titanium investment castings
  • Ask for failure history and corrective action records from previous titanium programs
  • Verify that the foundry uses process controls suited to low-melting titanium alloys

Titanium investment castings require specific foundry qualifications that exceed standard requirements for steel or nickel alloy parts. Aerospace buyers sourcing these components must verify that the foundry can manage heat, chemistry, and dimensional stability across the entire production cycle. This checklist covers the verification points necessary for titanium casting and investment casting applications.

Why titanium investment casting requires special verification

Titanium investment casting differs from steel or nickel alloy casting in several ways that directly affect quality and cost. Titanium has a low melting point relative to steel, making it highly susceptible to oxidation and nitridation during melting and solidification. The alloy also absorbs hydrogen easily, which can cause embrittlement if not managed strictly. Investment casting applications for titanium often involve complex geometries with thin walls, internal passages, or tight tolerances.

A foundry producing titanium investment castings must demonstrate control over raw materials, melting, investment, and post-casting heat treatment. Without these controls, parts may fail in service even if they pass initial dimensional inspection. The risk is not just in the casting process but in the entire chain of custody for the material. If a foundry treats titanium like a standard structural alloy, the resulting parts will likely have compromised mechanical properties.

Raw material and supply chain controls

Titanium casting quality begins with the feedstock. The foundry must be able to trace titanium billets or ingots back to certified mills. Buyers should request documentation showing alloy certification, heat numbers, and chemical analysis for the specific material lot used. This traceability is the foundation of the quality system.

Look for the following items in the foundry’s quality records:

  1. Mill test reports for titanium feedstock
  2. Chemical analysis certificates for the specific alloy designation
  3. Supplier qualification records for titanium mills
  4. Incoming inspection procedures for raw materials
  5. Segregation and storage controls for titanium inventory

Red flags include foundries that cannot provide heat traceability, that mix different titanium alloys in storage, or that rely on unverified secondary suppliers. Titanium billets should be stored in a way that prevents contamination with other materials. Mixing Ti-6Al-4V with Ti-10V-2Fe-1Al or pure titanium in the same rack creates a high risk of material misidentification. The foundry must have a system to physically separate these materials and document their movement.

Melting and process controls

Titanium melting requires controlled atmosphere or vacuum conditions. Conventional open-air melting introduces oxygen and nitrogen, which degrade the alloy. The foundry should use vacuum induction melting or inert gas shielding to protect the melt. This step is non-negotiable for high-integrity parts.

Ask the foundry to describe its melting process in detail. Key questions include:

  • Does the foundry use vacuum induction melting or inert gas shielding?
  • What is the maximum melt temperature and cooling rate?
  • How is hydrogen content controlled during melting?
  • Are there specific furnace procedures for different titanium alloys?
  • What monitoring instruments are used to verify atmosphere conditions?

A credible foundry will explain its process without vague language. If a foundry cannot describe its atmosphere controls or refuses to share process parameters, treat that as a red flag. The type of furnace used matters. A foundry using a standard crucible furnace without proper shielding will not produce the required quality. The monitoring instruments must be calibrated and capable of detecting small changes in atmosphere composition.

Investment and casting process verification

Investment casting applications for titanium require careful control of the investment system. The foundry must demonstrate that its investment materials and processes are compatible with titanium. Key verification points include:

  • Investment material suppliers and qualification records
  • Burnout procedures and temperature profiles
  • Casting temperature control for titanium
  • Handling procedures to prevent contamination
  • Core and gate design controls for complex geometries

Buyers should request examples of investment systems used for titanium. Ask for documentation of burnout cycles, investment material certifications, and any special handling requirements. Red flags include foundries that use the same investment process for titanium as for steel without documented adaptation. The investment material must withstand the high temperatures of titanium melting without releasing harmful gases. The burnout process must be slow enough to remove all organic residues without cracking the shell.

Dimensional inspection and quality control

Dimensional accuracy is critical for aerospace casting components. Titanium investment castings often have tight tolerances, especially for parts that mate with machined components or form functional surfaces. The foundry should use appropriate inspection methods for each part.

Common inspection methods include:

  • CMM (coordinate measuring machine)
  • Laser scanning
  • Optical comparison
  • Calipers and micrometers
  • Thread gauges for internal and external threads

The foundry should provide a dimensional inspection plan for each part. This plan should specify which features are inspected, what tolerance applies, and which method is used. Buyers should verify that the foundry’s measurement systems are calibrated and traceable to national standards. A CMM is useful for complex shapes, but it must be used by trained operators who understand the part’s critical features.

Red flags include foundries that cannot specify measurement uncertainty for critical dimensions, that skip first-article inspection, or that do not maintain calibration records for inspection equipment. If a foundry reports a dimension without stating the uncertainty of the measurement, the data is not useful for quality assurance.

Post-casting heat treatment

Post-casting heat treatment is often required for titanium investment castings. The heat treatment process affects mechanical properties, residual stress, and dimensional stability. The foundry must be able to perform heat treatment in a controlled atmosphere or vacuum environment. This step stabilizes the microstructure and prepares the part for machining.

Ask the foundry to provide:

  • Heat treatment procedures for each titanium alloy
  • Furnace type and atmosphere control method
  • Temperature uniformity verification records
  • Cooling rate controls
  • Documentation of heat treatment cycles

For aerospace casting, heat treatment records are typically part of the quality package. The foundry should provide certificates of heat treatment for each lot. Red flags include foundries that cannot specify atmosphere composition, that use air furnaces for titanium, or that cannot provide cycle documentation. Air furnaces introduce oxidation and will ruin the surface quality of the part. The furnace must have the ability to hold temperature uniformly across the load.

Documentation and traceability

Aerospace casting requires rigorous documentation. The foundry should maintain traceability from raw material to finished part. This includes heat numbers, process records, inspection results, and heat treatment certificates. The documentation is what proves the part is safe for service.

A complete documentation package for titanium investment casting should include:

  • Material certification
  • Process records
  • Dimensional inspection reports
  • Heat treatment certificates
  • Nondestructive inspection records
  • Final acceptance certificate

The foundry should be able to provide this documentation within a defined timeframe after part delivery. Red flags include foundries that provide incomplete records, that do not maintain traceability, or that resist providing documentation to the buyer’s quality team. If a foundry cannot provide the heat number for a specific part, the part is effectively untraceable and should be rejected.

Failure history and corrective actions

Review the foundry’s failure history for titanium programs. Ask about past issues with porosity, dimensional drift, heat treatment defects, or surface contamination. A credible foundry will share examples of failures and the corrective actions taken. This transparency builds trust.

Ask the foundry to describe:

  • Failure modes observed in previous titanium castings
  • Root cause analysis methods
  • Corrective action records
  • Preventive measures implemented
  • Customer complaint handling procedures

A foundry that has experienced failures and corrected them is often more trustworthy than one that claims no problems. The key is whether the foundry has a system for detecting, analyzing, and correcting issues. A foundry that hides its problems is a greater risk than one that openly discusses them.

Practical audit checklist

Use the table below as a practical audit checklist when evaluating a foundry for titanium investment casting. Each item should be verified during the audit or requested in writing.

Verification Item What to Check Red Flag
Raw material traceability Mill test reports, heat numbers, supplier records No heat traceability
Melting process Vacuum or inert gas shielding, atmosphere monitoring Open-air melting
Investment system Investment material qualification, burnout records Generic investment process
Dimensional inspection CMM or laser scanning, calibration records No measurement uncertainty data
Heat treatment Furnace type, atmosphere control, cycle records Air furnace for titanium
Documentation Complete quality package, traceability Incomplete records

Final verification steps

Before releasing a purchase order for titanium investment castings, complete the following final steps:

  1. Request a first-article inspection report
  2. Review the foundry’s quality management system
  3. Verify calibration records for inspection equipment
  4. Confirm heat treatment capability in writing
  5. Agree on acceptance criteria and documentation requirements

A foundry that passes these checks is more likely to deliver titanium investment castings that meet aerospace casting requirements. The checklist above provides a structured approach to verifying capability before committing to production.

Frequently asked questions

What is the most common failure mode in titanium investment casting?

Hydrogen absorption and oxidation during melting or casting are common failure modes. They can cause embrittlement or surface defects if atmosphere controls are inadequate.

How do I verify a foundry's heat treatment capability for titanium?

Request furnace type documentation, atmosphere control specifications, and cycle records. Verify that the foundry uses vacuum or inert gas furnaces and can provide heat treatment certificates.

What documents should I require from a foundry for aerospace casting?

Require material certification, process records, dimensional inspection reports, heat treatment certificates, nondestructive inspection records, and final acceptance certificates.

Can a foundry that produces steel castings also produce titanium castings?

Some foundries can, but titanium requires specific controls. Verify that the foundry has experience with titanium, uses appropriate melting and heat treatment equipment, and can provide titanium-specific documentation.

What is the typical tolerance range for titanium investment castings?

Tolerances depend on the part and application. Aerospace casting often requires tight tolerances on critical features. Specify tolerances in the drawing and verify that the foundry's inspection methods can hold them.