Independent investment casting knowledge for global buyersB2B Network
Investment Casting Hub
Defects & Inspection

Checklist: Verifying Foundry NDE Reports for Castings

Published Updated 5 min read

An engineer reviews a nondestructive testing report on a clipboard
Quick answer

Verify NDE report verification by checking report headers, test parameters, acceptance criteria, and defect locations. This guide lists specific data points buyers must confirm on certificates to ensure inspection documentation is complete and quality audit standards are met.

Key takeaways
  • A valid NDE report must list the specific test method, equipment ID, and acceptance criteria used.
  • Always verify that the part serial number and drawing revision on the certificate match the physical casting.
  • Red flags include missing operator qualifications, unexplained deviations from the test plan, and vague defect descriptions.
  • Use a structured quality audit to cross-reference NDE results against your Buyer's Guide to Investment Casting Defect Acceptance Criteria.

Why NDE Report Verification Matters in Casting Purchases

Non-destructive testing certificates are the primary proof that a casting passed its required inspection stages. However, a report is only as strong as the data it contains. Buyers and importers often receive generic documentation that lacks the specificity needed for a real quality audit. Without proper NDE report verification, a “pass” stamp does not guarantee the part is safe for service.

This checklist focuses on the specific data points you must check on non-destructive testing certificates. It is designed for engineers and procurement teams who need to validate inspection documentation before releasing shipments or initiating a supplier corrective action.

Check the Report Identity and Traceability

The first step in NDE report verification is confirming that the document belongs to the part you are inspecting. Mismatched identifiers are a common source of documentation errors, especially when multiple lots are tested in a single shift.

  1. Part Identification: Does the report list the casting part number, drawing number, and revision level? The revision level is critical. A drawing revision change often alters the critical features or defect acceptance limits.
  2. Lot or Heat Number: For investment castings, the heat number identifies the specific batch of molten metal. Verify this matches the material test report.
  3. Date and Time: The date must correspond to the production date or the actual test date. Check that the time is specific enough to correlate with the foundry’s production log.
  4. Unique Report ID: A professional foundry assigns a unique ID to each certificate. This allows you to cross-reference the report in their quality management system.

If any of these identifiers are missing or vague, the document fails the basic traceability check.

Verify Test Method and Equipment Specifications

Not all NDE methods are equal. A report that simply says “X-ray done” is insufficient. You need to know exactly how the test was performed to judge its sensitivity.

Key Data Points to Check

Data Point What to Look For Why It Matters
Test Method Specific standard (e.g., radiographic, ultrasonic, eddy current) Determines the type of defect detected
Equipment ID Unique ID of the X-ray tube or UT probe Ensures the tool was calibrated and maintained
Penetration Depth Maximum thickness tested (for RT/UT) Confirms the method can see through the section
Voltage/Parameters kV for RT, frequency for UT/EC Affects sensitivity to porosity and cracks
View Angle For RT, the specific view angle (e.g., 90 degree) Ensures the defect is not hidden by geometry

Red Flags

  • Missing Equipment ID: If the report does not list the specific X-ray tube or ultrasonic transducer ID, the calibration history cannot be verified.
  • Generic Method Statements: “Radiographic inspection performed” without specifying the voltage or view angle is a red flag.
  • Outdated Standards: If the report cites a standard version from several years ago, check if the foundry has updated their procedures.

Confirm Acceptance Criteria and Standards

Every inspection must be judged against a defined set of rules. NDE report verification requires that the acceptance criteria are clearly stated on the certificate.

  1. Standard Cited: The report should list the specific industry standard or internal specification used (e.g., ASTM, EN, or a customer-specific drawing note).
  2. Critical Feature Identification: If the casting has specific high-stress areas, the report should note if those areas received additional inspection.
  3. Defect Limits: For porosity, the report should state the maximum allowed size or quantity. For cracks, it should state the maximum length or depth permitted.
  4. Pass/Fail Definition: The report must explicitly state whether the part passed or failed. A “conforms to requirements” statement is acceptable only if the requirements are clearly defined elsewhere.

If the acceptance criteria are not on the report or are ambiguous, the “pass” is meaningless. You need to know exactly what was allowed and what was not.

Inspect Defect Descriptions and Locations

When a defect is found, the description must be precise enough to allow for repair or rejection. Vague descriptions are a major risk in quality audit processes.

Required Defect Data

  • Location: Use a coordinate system or a marked drawing. “Near the boss” is not specific enough. “0.5 inch below the parting line on the flange” is specific.
  • Size: Length, width, and depth for cracks. Diameter for porosity clusters.
  • Type: Porosity, crack, tear, or other.
  • Quantity: Total number of defects found in that area.

Red Flags

  • Unexplained “Conformity”: If the report says “no significant defects” without defining what “significant” means, it is not a valid NDE report verification document.
  • Missing Sketch: For complex castings, a simple sketch highlighting the defect location is often required.
  • Inconsistent Terminology: Mixing terms like “shrinkage” and “porosity” without defining the distinction can lead to misinterpretation.

Review Operator Qualifications and Calibration

The human element and the equipment health are both part of the NDE report verification process. A skilled operator using calibrated equipment is the baseline for a valid test.

  1. Operator Name and ID: The report should list the name of the person performing the test.
  2. Qualification Level: Check that the operator is qualified for the specific method and material thickness. For example, a Level I ultrasonic technician may not be qualified to inspect thick wall sections that require Level II or III skills.
  3. Calibration Dates: For X-ray systems, the report or its reference should confirm that the equipment was calibrated within the required interval.
  4. Review Engineer: A second person should verify the report. Look for a second signature or a “Reviewed By” field.

If the operator is not listed or their qualification level is below what is required for the section thickness, the inspection may be invalid.

Final Quality Audit Checklist

Use this summary list for your final NDE report verification before accepting the shipment.

  1. Part number, drawing, and revision match the purchase order.
  2. Heat number matches the material certificate.
  3. Test method is specified with parameters (kV, frequency, etc.).
  4. Equipment ID is listed.
  5. Acceptance criteria are cited and defined.
  6. All defects are described with size and location.
  7. Operator and reviewer are identified.
  8. Report is signed and dated.

If you find discrepancies in any of these areas, initiate a quality audit with the foundry. Request a re-inspection or a detailed explanation before releasing the parts.

Common Mistakes in NDE Report Verification

Buyers often overlook subtle errors that compromise the validity of the inspection documentation.

  • Ignoring Drawing Revisions: A part made to Rev. A might have different acceptance criteria than Rev. B. Always check the revision.
  • Assuming “Pass” Means “Perfect”: A pass means the part meets the specified limits, not that it is free of all defects.
  • Skipping the Calibration Check: An uncalibrated X-ray tube can produce false negatives, missing internal porosity.
  • Accepting Verbal Confirmations: Always require the written NDE report. Verbal assurances do not provide a quality audit trail.

By following this checklist, you ensure that your NDE report verification process is rigorous and that the inspection documentation supports your quality audit standards.

Frequently asked questions

Can I use an X-ray report as proof of ultrasonic inspection?

No. X-ray and ultrasonic tests detect different types of defects. X-ray is best for internal porosity, while ultrasonic is better for surface-breaking cracks. They cannot be substituted for each other.

What if the NDE report does not list the equipment ID?

This is a red flag. You should request the equipment ID and its calibration certificate. Without it, you cannot verify that the tool was functioning correctly during the test.

How specific should defect locations be on the report?

Locations should be specific enough to be replicated. Use coordinates, distances from reference features, or a marked drawing. "Near the corner" is not specific enough for a quality audit.

Do I need to check the operator's qualification level?

Yes. The operator must be qualified for the specific method and material thickness. A lower-level qualification may result in missed defects in thicker sections.

What should I do if the report is missing acceptance criteria?

Do not release the part. Request that the foundry provide a revised report that explicitly states the standard used and the pass/fail limits applied to the test.