Troubleshooting: Hot Tears in Cast Stainless Steel

Hot tears in stainless steel investment castings appear when the solid shell cracks under tensile stress during freezing. This guide lists common symptoms, likely causes, and practical fixes to reduce stainless steel casting defects and improve investment casting troubleshooting results.
- Hot tears are stress cracks in the solidifying shell, not porosity.
- Stainless steel freezes over a wide range, which increases hot tear risk.
- Fixing the thermal gradient and mold strength usually solves most cases.
- Design changes like thicker walls and fillets reduce the problem.
Hot tears in castings show up as open cracks or splits in the solid shell of a stainless steel investment casting. The defect forms while the part is still partially molten inside. It is a common issue in stainless steel because the alloy solidifies over a wider temperature range than many carbon steels. The solid outer layer cools and shrinks while the inner core remains liquid. That mismatch creates tensile stress. If the stress exceeds the strength of the semi-solid metal, the shell cracks.
Why stainless steel is more prone to hot tears
Stainless steels are often considered difficult to cast for a few practical reasons. The alloy system freezes over a broad temperature window. This means there is a long period where the metal is in a two-phase state, partly solid and partly liquid. The solid phase forms a network that must support itself. If the liquid inside moves or shrinks, it pulls on that network.
The thermal conductivity of stainless steel is also lower than many other steels. Heat escapes more slowly. The mold surface stays hotter for longer. That can keep the casting surface in a soft state for more time. The casting is more likely to deform under its own weight or from mold pressure before it becomes strong enough to resist it.
Symptom checklist before changing the process
Do not jump straight to a new alloy or a new supplier. First, confirm that the defect is a hot tear. The appearance of the crack matters. A hot tear usually has a clean, flat, or slightly rounded face. It can look like a sharp line or a wider split. The edges may be slightly rounded because the liquid metal flowed into the crack before it froze. The crack often follows the direction of the part’s main stress path, such as across a thin section, around a fillet, or across a change in thickness.
If the crack is full of gas pockets, it is more likely a shrinkage cavity or a gas porosity issue. If the crack is on the part surface but the interior is sound, it may be a mold tear or a surface break from handling. A proper visual check should be paired with a cross-section if the part is critical. Cutting the casting open often reveals how far the crack has penetrated.
Troubleshooting table for common hot tear patterns
| Symptom | Likely cause | What to do |
|---|---|---|
| Cracks across thin sections or web areas | High tensile stress from uneven cooling and low local strength | Add local chill, thicken the wall, or relocate the gate |
| Cracks near fillets or corners | Stress concentration at abrupt geometry changes | Increase fillet radius and smooth the mold surface |
| Cracks along the mold parting line | Mold pressure or shrinkage pulling the shell apart | Check mold strength, reduce mold pressure, or add backing |
| Multiple small cracks on a large flat area | Poor feed or excessive cooling rate across the surface | Improve feeding, slow the cooling rate, or add a chill |
| Cracks in the core or core line | Core shrinkage or core movement during solidification | Improve core venting, tighten core fit, or add local support |
Fixing the thermal gradient
The most common fix involves changing how heat leaves the casting. The goal is to keep the critical sections solid longer and reduce the temperature difference between the surface and the core. Adding a local chill to the mold surface can help. The chill draws heat away from a specific area and directs the solidification front in a controlled way. This is useful when the crack appears in a thick section or near a gate.
If the part has a thin web, the web may be freezing too fast. The surface hardens before the interior is strong enough. Slowing the cooling rate of the thin section can reduce the stress. This can be done by adding a small sand or ceramic pad to the mold surface, or by reducing the intensity of the chill nearby. The idea is to keep the metal in a two-phase state long enough for it to feed itself.
Managing mold pressure and strength
Mold pressure can also cause hot tears. If the mold is too weak, the molten metal can push the mold surface outward before the casting is strong. That movement tears the semi-solid shell. If the mold is too strong, it can hold the casting in place and prevent natural feed flow. Both extremes can cause problems.
Check the mold composition and packing. In investment casting, the shell strength depends on the refractory, binder, and firing process. A shell that has not fired properly may be too brittle or too weak. A shell that has fired too hard may be too rigid. The firing curve should match the alloy and the part geometry. A slightly softer shell can absorb more strain before it cracks. A harder shell can resist deformation better but may not allow feed.
Design changes that reduce hot tear risk
Geometry is a major factor. Sharp corners and abrupt changes in thickness create stress concentrations. Increase fillet radii where possible. Avoid thin webs that span a large distance. If a thin section is required, add a local reinforcement or a gate nearby. A gate close to a thin section can feed it more effectively. It also helps control the direction of solidification.
Thicker sections are usually better for hot tear resistance, but they can cause other defects like shrinkage porosity. The design should balance thickness with feeding. A slightly thicker wall with a good feeding path is often better than a very thick wall with no gate nearby. The goal is to let the casting solidify in a controlled direction, with a clear feed path to the last liquid area.
Inspection and process control
Prevent hot tears by checking the process at every stage. The investment mixture, firing schedule, and pouring temperature all affect the result. A higher pouring temperature can increase the thermal gradient and make hot tears worse. A lower temperature can reduce the flow and cause other defects. Find the balance for the specific alloy and part.
Use a consistent pouring rate. A slow pour can reduce splashing and air entrapment. A fast pour can increase the thermal shock on the mold surface. The pouring technique should match the gating design. If the gate is small, a slower pour is often better. If the gate is large, a faster pour may be needed to fill the part before the metal cools.
When to involve the foundry
If the hot tears persist after process changes, the issue may be deeper than a single variable. It may be a combination of alloy behavior, mold quality, and design. A foundry engineer can review the cross-section, the mold, and the gating. They can suggest a local chill, a different firing schedule, or a small design change. In some cases, a different stainless steel grade may be needed. Some grades are more prone to hot tears than others. The choice depends on the part requirements and the expected service conditions.
Prevention tips
- Increase fillet radii in all internal corners.
- Avoid thin webs that span a large distance.
- Add local chills to thick sections and near gates.
- Check the shell strength and firing schedule regularly.
- Use a consistent pouring rate and temperature.
- Review the gating design for feed paths to critical areas.
- Cross-section suspect parts to confirm the defect type.
- Keep a record of process changes and defect patterns.
Frequently asked questions
How do I tell a hot tear from a shrinkage cavity?
A hot tear is a crack in the solid shell with clean or rounded edges. A shrinkage cavity is a void, often round or irregular, filled with gas or empty. A cross-section is the best way to confirm.
Can hot tears be repaired after casting?
Some hot tears can be repaired by grinding and rewelding if the part allows it. For critical parts, it is better to fix the cause and re-cast the part.
Does the stainless steel grade matter?
Yes. Some stainless grades are more prone to hot tears than others. The alloy composition and solidification range affect the risk. Choose a grade that balances strength and castability.
Is a hot tear always a failure?
Not always. A small hot tear on a non-critical surface may be acceptable. For pressure parts or safety parts, it is usually a defect that must be eliminated.
Can changing the mold material fix hot tears?
It can help. A mold with better strength or a different thermal property can reduce the stress on the casting shell. The change should be based on the specific defect pattern.


