Independent investment casting knowledge for global buyersB2B Network
Investment Casting Hub
Alloys & Materials

How to Specify Tolerances for Cast Titanium Parts

Published Updated 7 min read

Close up view of a titanium casting investment mold section
Quick answer

Specifying tolerances for titanium casting requires understanding how the alloy shrinks and cools. You must balance tight dimensional limits with the structural integrity of the part. This guide provides a step-by-step method to define acceptable limits for investment cast titanium components.

Key takeaways
  • Define tolerance limits based on the functional requirement of the part, not just the drawing limit.
  • Account for the thermal contraction of titanium alloy during the solidification process.
  • Separate critical features from non-critical features to manage manufacturing costs.
  • Use a stepwise verification process to ensure the final cast part meets the specified limits.

Specifying tolerances for titanium casting is a balance between design intent and process reality. Investment casting produces intricate geometry with thin walls, but the alloy behavior during cooling changes the final dimensions. Engineers and buyers must define these limits clearly to avoid rejection of otherwise good parts.

This guide walks through the prerequisites and steps needed to set acceptable dimensional limits. It assumes you are working with a titanium alloy, such as Ti-6Al-4V, which is the most common choice for structural aerospace and industrial components. The process applies to any investment cast titanium part, from a small bracket to a larger valve housing.

Prerequisites for Tolerance Specification

Before setting numbers on a drawing, you need three baseline inputs. These inputs drive every subsequent decision.

First, you need the functional requirement. Does the part need to mate with a machined surface? Is it a pressure boundary? Or is it a cosmetic cover? A mating surface demands much tighter limits than a non-functional face.

Second, you need the process capability data. Every foundry has a specific ability to hold dimensions. Some casters can hold tight limits on small parts. Others are better suited for larger, heavier sections. You must know the capabilities of the specific titanium casting facility you are using.

Third, you need the alloy behavior. Titanium alloys do not shrink uniformly. The rate of contraction depends on the cooling speed, the alloy chemistry, and the thickness of the section. A thin wall cools faster than a thick boss. This difference in cooling creates differential shrinkage.

Without these three inputs, any tolerance specification is a guess. You are setting limits without knowing if the process can meet them.

Step 1: Identify Critical Features

Start by marking the features on your CAD model that dictate function. A “critical” feature is one where a deviation prevents the part from working.

For a titanium casting used in an engine, a bolt hole location is critical. If the hole shifts, the bolt will not align with the mating flange. A flat surface that only touches a gasket is critical. A surface that only holds a label is not.

Create a table in your specification. List each critical feature. Assign a tolerance class to each one. A standard tolerance class is a general range, such as plus or minus a specific amount. For high-precision parts, you might use a tighter class. For non-critical features, you can use a looser class.

The reason for this step is cost control. Holding a tight tolerance on every feature increases the rejection rate and the machining cost. You only pay for precision where the part needs it.

Step 2: Define the Tolerance Class

Select a tolerance class for each critical feature. The class determines the allowable deviation from the nominal dimension.

A typical approach is to use a general tolerance for the entire part, then override specific features. The general tolerance covers the non-critical dimensions. The overrides cover the critical ones.

For example, a general tolerance might be plus or minus 0.10 mm. A critical bolt hole might be overridden to plus or minus 0.05 mm. A mating face might be overridden to plus or minus 0.02 mm.

The reason for using a general tolerance with overrides is clarity. It tells the foundry what is expected across the whole part. It also tells them where to focus their inspection effort. If you specify a tight tolerance on every single dimension, the foundry must inspect every single dimension. This is expensive and slow.

Step 3: Account for Thermal Shrinkage

Titanium alloy shrinks as it cools from the liquid state to the solid state. This shrinkage is not uniform. It depends on the cooling rate and the geometry.

You must apply a shrinkage allowance to your nominal dimensions. This allowance is a small adjustment to the casting size so that the part ends up at the correct size after cooling.

For a thick section, the shrinkage is greater than for a thin section. A 10 mm thick wall will shrink more than a 3 mm thick wall. You need to calculate this difference for your specific part.

The reason for this step is accuracy. If you do not account for shrinkage, the part will be out of size. It will be either too big or too small. This leads to excessive machining or rejection. The foundry can apply this allowance, but you must specify it or provide the data.

Step 4: Consider the Casting Process

Investment casting has specific characteristics that affect tolerances. The part is formed by a wax pattern, which is dipped in a ceramic shell. The shell is heated, the wax is burned out, and the metal is poured in.

The cooling happens in the shell. The shell insulates the part. This slow cooling allows for better dimensional stability. However, the shell also traps the metal. It slows down the heat transfer.

This slow cooling reduces the thermal gradients. It means the part shrinks more uniformly. This is an advantage for tight tolerances. However, it also means that the part takes longer to cool. The foundry must manage this time.

The reason for this step is process understanding. You are not just specifying a number. You are specifying a result that a specific process must achieve. You need to know if the process can hold the limit. If the process is too slow, the part might warp. If the process is too fast, the part might shrink unevenly.

Step 5: Specify Inspection and Verification Methods

You must state how the part will be checked. A tolerance is meaningless without a method to measure it.

For small parts, use a CMM, which stands for Coordinate Measuring Machine. It uses a probe to touch the part and measure the coordinates. It is very accurate and is good for complex geometry.

For large parts, use a laser tracker or a laser scanner. These tools measure the part from a distance. They are good for large surfaces and can map the entire part.

For internal features, use a bore gauge or a plug gauge. These are simple tools that check the size of a hole or a pin.

The reason for this step is accountability. If you specify a tolerance but do not specify how it is measured, the foundry and the buyer might disagree on the result. You need a common standard.

Step 6: Review for Feasibility with the Foundry

Send your specification to the foundry. Ask them to review it.

The foundry will check if the tolerances are achievable. They will look at the geometry, the alloy, and the process. They will tell you if any dimension is too tight.

If a dimension is too tight, you have two choices. You can loosen the tolerance. Or you can change the design. You might add a machining step. Or you might change the geometry to make the part easier to cast.

The reason for this step is partnership. The foundry has the process knowledge. You have the design intent. You need both. If you do not talk to the foundry early, you might find out about a problem after the part has been cast. That is expensive and slow.

Common Mistakes in Tolerance Specification

There are several errors that engineers make when specifying tolerances for titanium casting.

The first mistake is applying a general tolerance to every feature. This forces the foundry to hold tight limits on non-critical dimensions. It increases cost and rejection risk.

The second mistake is ignoring shrinkage. If you do not apply a shrinkage allowance, the part will be out of size. You will have to machine it or reject it.

The third mistake is not specifying the inspection method. If you do not say how the part will be measured, you will have disputes later.

The fourth mistake is not reviewing the specification with the foundry. If you do not talk to the foundry, you might find out about a problem too late.

Final Verification Step

Before releasing the drawing for production, you must verify the specification.

Check every dimension. Check the tolerance class. Check the inspection method. Check the shrinkage allowance.

Make sure the specification is clear and complete. Make sure the foundry has all the information they need.

The reason for this step is to avoid errors. A single typo can cause a part to be out of size. A missing inspection method can cause a dispute. Verification catches these errors before they become problems.

Feature Type Tolerance Class Inspection Method
Critical Mating Surface Plus or minus 0.02 mm CMM
Bolt Hole Location Plus or minus 0.05 mm CMM
General Part Dimension Plus or minus 0.10 mm CMM or Caliper
Internal Bore Plus or minus 0.08 mm Bore Gauge
Cosmetic Surface Plus or minus 0.20 mm Visual or Caliper

Final Thoughts

Specifying tolerances for titanium casting is a technical task. It requires an understanding of the alloy, the process, and the function of the part.

You must define the critical features. You must select the tolerance class. You must account for shrinkage. You must specify the inspection method. And you must review the specification with the foundry.

If you follow these steps, you will have a specification that is clear and achievable. You will reduce rejection rates and control costs. You will get a titanium part that fits your design intent.

Frequently asked questions

What is the standard tolerance for a titanium casting?

There is no single standard tolerance. It depends on the feature and the process. A general tolerance is often plus or minus 0.10 mm, but critical features require tighter limits.

Can I hold a tolerance of plus or minus 0.01 mm on a large titanium casting?

It is difficult for large parts. Large parts have more thermal gradients and shrinkage variation. You might need to add a machining step to achieve that level of precision.

How does the alloy affect the tolerance?

The alloy affects the shrinkage rate. Different titanium alloys have different coefficients of thermal expansion. You must use the correct shrinkage allowance for the specific alloy.

Do I need to specify the shrinkage allowance on the drawing?

It is best practice to specify it. Some foundries apply a standard allowance. Others require you to provide the data. Check with the foundry before releasing the drawing.

What is the best way to verify the tolerance?

Use a CMM for small parts and a laser tracker for large parts. Specify the method in the drawing so that the foundry and the buyer use the same standard.