Checklist: Verifying Tensile Data for Cast Steel

This guide provides a numbered audit checklist for verifying cast steel tensile data. It helps buyers and engineers validate foundry test reports by checking standards, witness bars, heat traceability, and common reporting errors before acceptance.
- Verify that tensile data matches the specific heat number and alloy composition of the received material.
- Check test reports for the correct standard, test bar orientation, and witness bar results.
- Look for red flags such as missing witness data, inconsistent heat numbers, and unexplained property variations.
- Confirm that material verification aligns with the purchase order specifications and applicable industry standards.
- Request raw test data sheets and certificates of analysis when discrepancies appear in summary reports.
Why Verify Tensile Data Before Acceptance
Foundry tensile reports are the primary evidence that a cast steel part meets the mechanical requirements of the purchase order. However, a report on paper does not guarantee the material performance in the field. Buyers and engineers must verify that the data is accurate, traceable, and consistent with the actual material received. This checklist provides a structured approach to auditing those documents.
The process focuses on three areas: the test procedure itself, the traceability of the heat, and the consistency of the results. Each item below asks a specific question and explains what to look for in the foundry report.
Does the Report Reference the Correct Test Standard?
The test standard defines how the specimen is prepared, oriented, and loaded. Without the correct standard, the numbers cannot be compared to specifications or previous lots.
- Identify the standard cited on the report. Common references include ASTM E8/E8M or ISO 6955, depending on the region and alloy class.
- Confirm the standard version year matches the specification on the purchase order.
- Check that the test type is tensile testing, not hardness or impact testing, unless those are the specified properties.
Red flags:
- The report lists multiple standards without clarifying which one was used.
- The standard cited is for a different alloy family or material form.
- The report uses a non-standard test method without prior customer approval.
If the standard is missing, the data lacks context. A tensile strength value of 620 MPa means something different under one standard versus another, especially when specimen geometry differs.
Are the Specimen Details and Orientation Documented?
Tensile strength is sensitive to specimen orientation relative to the casting flow. Investment casting produces parts with complex flow patterns, and the direction of the tensile bar matters.
- Check the orientation of the tensile bar relative to the part or mold.
- Verify the specimen geometry, such as the gauge length and diameter.
- Confirm that the test was performed on a witness bar, not a machined section of the final part.
Red flags:
- No orientation is specified, or the orientation is described vaguely.
- The report states the test was done on the finished part without mentioning a witness bar.
- Specimen dimensions differ from the standard without explanation.
Witness bars are critical for investment casting. They are cast alongside the production parts in the same mold or heat. Testing the finished part can introduce errors from machining, surface finish, or distortion. If the foundry cannot provide witness bar data, the tensile results for the entire heat are suspect.
Does the Heat Number Match Across All Documents?
Heat traceability links the material to the raw ingredients, melting process, and pouring. A mismatch here breaks the chain of custody and invalidates the material verification.
- Compare the heat number on the tensile report with the heat number on the mill certificate or heat analysis.
- Check that the heat number appears on the packing list, purchase order acknowledgment, and any material certificates.
- Verify that the alloy composition on the heat analysis falls within the specification limits.
Red flags:
- Different heat numbers appear on different documents for the same shipment.
- The heat number is missing from the tensile report.
- The composition analysis shows elements outside the specified range without a note.
If the heat number changes between documents, it suggests the foundry may have mixed materials from different melts. This is a serious quality control failure. Always request a consolidated material package that includes the heat analysis, tensile report, and dimensional inspection report under a single heat number.
Are the Tensile Results Consistent and Within Limits?
Individual values matter, but trends matter more. A single high value might be a lucky draw, but a cluster of low values indicates a process problem.
- Check the average tensile strength, yield strength, and elongation against the purchase order limits.
- Look at the minimum values, not just the average.
- Review the number of tests performed. Most standards require a minimum number of specimens per heat.
Red flags:
- One test result fails while others pass, without a noted reason.
- The average is within limits but the minimum is below the specification.
- The number of tests performed is fewer than required by the standard.
For cast steel, elongation is often a better indicator of process health than strength alone. Low elongation can point to excessive cooling rates, improper heat treatment, or compositional shifts. If elongation trends low across multiple heats, discuss the process with the foundry before accepting future lots.
What Is the Relationship Between Tensile Data and Hardness or Impact Data?
Tensile tests are not the only mechanical property that matters. For many applications, hardness or impact resistance is equally important. The tensile data should be viewed in context.
- Check if hardness or impact data is provided on the same report or in a companion document.
- Ensure the hardness test standard matches the tensile test standard in terms of material state.
- Verify that the heat treatment condition is specified. Cast steel is often supplied in as-cast, normalized, or quenched and tempered conditions.
Red flags:
- Tensile data is provided without any mention of heat treatment condition.
- Hardness values are inconsistent with the expected range for the alloy and condition.
- The report does not distinguish between as-cast and heat-treated properties.
If the purchase order requires a specific heat treatment, the tensile data must reflect that condition. As-cast cast steel is softer and more ductile than quenched and tempered steel. Mixing these up leads to incorrect material selection and potential part failure.
How to Handle Discrepancies or Missing Data
Sometimes the report is incomplete or contains errors. Knowing how to respond protects the project and maintains a constructive relationship with the foundry.
- Document the specific discrepancy in writing.
- Request a corrected report or additional test data.
- Hold acceptance of the material until the issue is resolved.
Red flags:
- The foundry refuses to provide raw test data or witness bar results.
- Corrections are made without explaining the root cause.
- The foundry suggests accepting the material based on “typical” properties rather than actual test results.
If a foundry is unwilling to provide full traceability or test data, it is a sign of weak quality systems. Consider whether the relationship can support the project risk. For critical applications, missing data is not a minor inconvenience; it is a quality control failure.
Red Flags Summary Table
Use this table as a quick reference when reviewing a tensile report.
| Check Item | What to Look For | Red Flag |
|---|---|---|
| Test Standard | Correct standard and version year | Missing standard or version mismatch |
| Specimen Orientation | Orientation relative to casting flow | No orientation specified |
| Witness Bar | Data from a witness bar, not the part | No witness bar data provided |
| Heat Number | Matches all other documents | Inconsistent heat numbers |
| Composition | Within specification limits | Elements out of range |
| Results | Minimum values within limits | One failure without explanation |
| Heat Treatment | Condition specified | Missing or ambiguous condition |
| Number of Tests | Meets standard minimum | Fewer tests than required |
Final Audit Steps
Before signing off on a shipment of cast steel, complete these final checks:
- Confirm the report is signed and dated by the foundry quality representative.
- Verify that the signature matches the authorized signatory on file.
- Ensure the report is archived with the purchase order and inspection records.
- Update your foundry quality scorecard based on the report completeness and accuracy.
- Communicate any findings to the foundry quality manager for process improvement.
A well-organized tensile report is a reflection of the foundry’s quality culture. Inconsistent or incomplete reports signal areas for improvement. Use this checklist as a baseline for every lot, not just the first one. Consistency in verification builds trust and reduces the risk of field failures.
Frequently asked questions
Can I use tensile data from a previous heat to verify a new shipment?
No. Tensile data is specific to the heat and the test condition. Always request new test data for each heat or verify that the new heat is from the same melt with full traceability.
What if the foundry only provides hardness data and no tensile data?
Hardness and tensile strength are related but not interchangeable. If the specification requires tensile properties, you must request tensile test results. Hardness alone does not verify strength or elongation.
How many tensile tests are typically required per heat?
The number depends on the applicable standard and the alloy class. Most standards require a minimum of two to three specimens per heat, with more for larger volumes or critical applications.
Does the orientation of the tensile bar matter for investment casting?
Yes. Investment casting creates complex flow patterns, and the direction of the tensile bar relative to the mold flow affects the measured strength and elongation. Always verify that the orientation is documented.
What should I do if the heat number on the tensile report does not match the heat analysis?
Stop the acceptance process and contact the foundry immediately. This discrepancy suggests a traceability failure. Request a corrected report and investigate the cause before proceeding.


